Fab Floors Heavy Wax Build-Up Remover

(20 Ounce Can × 12 Cans Per Case)

A clinging aerosol gel formulated to remove heavy wax and floor finish buildup from baseboards and other hard-to-reach vertical surfaces.

Overview
Fab Floors Heavy Wax Build-Up Remover is a powerful baseboard stripping aerosol designed to tackle excessive wax and finish accumulation in areas that are difficult to clean with traditional liquid strippers. Its inverted, clinging gel formula adheres to vertical surfaces, allowing extended dwell time to break down heavy buildup without excessive runoff. The product is engineered for use on baseboards, floors, and ceramic wall tile, and rinses clean with water when used according to directions, supporting efficient restoration prior to refinishing.

For Use On Baseboards, Vertical Surfaces, Metal Doors & Frames

✅ What This Product Is Used For
• Removing heavy wax and floor finish buildup
• Stripping baseboards and vertical surfaces
• Cleaning hard-to-reach areas where liquid strippers run off
• Preparing surfaces for refinishing
• Maintenance stripping in commercial environments

❌ What This Product Is Not For
• Painted or varnished surfaces
• Direct application to finished floors
• Routine daily cleaning
• Use without proper ventilation
• Residential household misuse

⚙️ Key Performance Advantages
• Clinging gel adheres to vertical surfaces
• Designed for upside-down application
• Breaks down heavy wax and finish buildup
• Easy rinsing with water after removal
• Effective in confined or detailed areas

🏢 Common Use Environments
• Commercial buildings
• Schools and universities
• Healthcare facilities
• Retail and office spaces
• Institutional maintenance operations

❓ Frequently Asked Questions

What surfaces is this product intended for?
It is intended for baseboards, floors, and ceramic wall tile where heavy wax or finish buildup is present.

Can this be sprayed in an upside-down position?
Yes. The product is designed with a special valve to be used upside down for vertical surface application.

Is this safe for painted or varnished surfaces?
No. It should not be used on painted or varnished surfaces, and overspray should be wiped off immediately.

How long should the product dwell before scrubbing?
Allow the product to dwell for 3–5 minutes, longer if buildup is substantial.

Does the product require rinsing?
Yes. After scrubbing, rinse thoroughly with clean water and allow the area to dry completely before refinishing.

Can the process be repeated if buildup remains?
Yes. Repeat the application until all wax buildup is removed.

🧪 Active Ingredient(s) or Core Composition
• Water – Base solvent for controlled cleaning action
• 2-Butoxyethanol – Solvent that breaks down wax and finish buildup
• Phosphated Mono/Diglyceride, Sodium Salt – Enhances penetration and cleaning effectiveness
• Sodium Hydroxide – Supports wax and finish removal
• Butane – Aerosol propellant
• Propane – Aerosol propellant

📌 Directions for Use (Summary)
Shake well before using. Test product on a small, inconspicuous area to ensure compatibility. Turn can upside down and hold 6–10 inches from the surface. Spray a thin, even coating to cover the wax buildup. Allow to dwell for 3–5 minutes, longer if buildup is heavy. Scrub the surface with an abrasive pad or scrub brush. Rinse thoroughly with clean water and allow the area to dry completely before refinishing. Repeat as necessary. Do not spray on painted or varnished surfaces and wipe off any overspray immediately.

⚠️ Safety & Handling
DANGER: Extremely flammable aerosol. Contains gas under pressure and may explode if heated. Causes skin irritation and serious eye irritation and may cause an allergic skin reaction. Keep away from heat, sparks, open flames, and hot surfaces. Do not smoke while using. Do not pierce or burn the container. Avoid breathing gas. Use with adequate ventilation. Wear protective gloves and eye protection. Store in a well-ventilated place, protect from sunlight, and do not expose to temperatures exceeding 49°C / 120°F. Keep out of reach of children.

🚛 Shipping & Compliance Notice
Proper Shipping Name: Aerosols, flammable
Hazard Class: 2.1
ID Number: UN1950
Packing Group: Not applicable

General Usage Limitation

This product is intended for professional, commercial, or industrial use only unless otherwise stated. The user is solely responsible for determining suitability for any specific application and for ensuring compliance with all applicable laws and regulations. Seismic Blends makes no warranties, express or implied, regarding fitness for a particular purpose or use beyond those explicitly stated. Misuse, improper handling, or failure to follow safety guidelines may result in damage or injury. Always review the Safety Data Sheet (SDS) and use appropriate personal protective equipment (PPE).